Linksys Wrt120n: A Simple Guide to Configuring Your Router as a Repeater
# Configurar Router Linksys Como Repetidor Wrt120n: Tips and Tricks for a Faster and More Reliable Wi-Fi Network
Do you have a Linksys Wrt120n router and want to use it as a repeater to extend your Wi-Fi signal? If so, you are in the right place. In this article, we will show you how to configure your router as a wireless repeater and improve your internet coverage.
## What is a wireless repeater?
A wireless repeater is a device that receives the Wi-Fi signal from your main router or access point and retransmits it to other areas of your home or office. This way, you can eliminate dead zones and enjoy a stronger and more consistent Wi-Fi connection.
## How to configure your Linksys Wrt120n router as a wireless repeater?
Before you start, you need to obtain the wireless settings of your main router or access point, such as the network name (SSID), the network band (2.4 GHz or 5 GHz), and the security mode (WPA-Personal, WPA2-Personal, or WPA-Mixed-Personal). You also need to make sure that your Linksys Wrt120n router has the latest firmware version installed.
To configure your router as a wireless repeater, follow these steps:
1. Connect your computer to one of the LAN ports of your Linksys Wrt120n router using an Ethernet cable.
2. Open your web browser and enter "http://192.168.1.1" in the address bar. This is the default IP address of your router. If you have changed it, use the new IP address instead.
3. Log in to your router's web-based setup page using the default username and password, which are both "admin". If you have changed them, use the new credentials instead.
4. Click on Connectivity and then on Internet Settings.
5. Click on Edit and then select Wireless Repeater.
6. Enter the network name (SSID), network band, and security mode of your main router or access point in the corresponding fields.
7. Click on Save Settings and then on Yes to confirm.
8. Wait for your router to reboot and become a wireless repeater.
## How to check if your wireless repeater is working?
To check if your wireless repeater is working, you can do the following:
- Scan for available Wi-Fi networks on your wireless devices and see if you can find the network name (SSID) of your main router or access point.
- Connect to the network and test the internet speed and stability using online tools such as speedtest.net or fast.com.
- Move around your home or office and see if you can get a good Wi-Fi signal in areas where you previously had poor or no coverage.
## How to troubleshoot common issues with your wireless repeater?
If you encounter any issues with your wireless repeater, such as not being able to connect to the network, having slow internet speed, or losing connection frequently, you can try these tips:
- Make sure that your main router or access point and your wireless repeater are using different channels to avoid interference. For example, if your main router or access point is using channel 1 on the 2.4 GHz band, set your wireless repeater to use channel 6 or 11 on the same band.
- Place your wireless repeater in a location that is close enough to receive a strong signal from your main router or access point, but far enough to cover the area where you need better Wi-Fi coverage. Avoid placing it near metal objects, walls, or other sources of interference that can weaken the signal.
- Adjust the antennas of your wireless repeater to improve the signal quality and direction.
- Update the firmware of your wireless repeater to fix any bugs or improve its performance.
- Reset your wireless repeater to factory defaults and reconfigure it as a wireless repeater if none of the above tips work.
## Conclusion
Configurar Router Linksys Como Repetidor Wrt120n
## How to access your Linksys Wrt120n router's web-based setup page in wireless repeater mode?
Once you have configured your router as a wireless repeater, you will need to use a different IP address to access its web-based setup page. This is because the router will no longer use the default IP address of 192.168.1.1, but will obtain a new IP address from your main router or access point's DHCP server.
To find out the new IP address of your router, you can do the following:
- Log in to your main router or access point's web-based setup page and look for the DHCP table or client list. This will show you the IP addresses of all the devices connected to your network, including your wireless repeater.
- Scan your network using a tool such as Advanced IP Scanner or Fing, which can detect the IP addresses and names of all the devices on your network.
- Use a ping command to test the connectivity between your computer and your wireless repeater. For example, if you know that your wireless repeater's MAC address is 00:11:22:33:44:55, you can use the command "ping -a 00:11:22:33:44:55" in a command prompt window and see if you get a reply with an IP address.
Once you have found out the new IP address of your router, you can enter it in your web browser's address bar and log in to its web-based setup page using the same username and password as before.
## How to change the wireless settings of your Linksys Wrt120n router in wireless repeater mode?
If you want to change the wireless settings of your router in wireless repeater mode, such as the network name (SSID), the security mode, or the password, you can do so by logging in to its web-based setup page using the new IP address.
However, you need to keep in mind that only one (1) frequency band on your router will be used for repeating the signal from your main router or access point. This means that if you change the wireless settings of that frequency band, you will also change the settings of the network that you are repeating.
For example, if you have configured your router to repeat the 2.4 GHz network of your main router or access point, and you change the network name (SSID) or password of that frequency band on your router, you will also change the network name (SSID) or password of the 2.4 GHz network that you are repeating. This may cause connection issues for other devices that are connected to that network.
Therefore, it is recommended that you do not change the wireless settings of the frequency band that you are using for repeating the signal. Instead, you can change the wireless settings of the other frequency band on your router, which can be used for broadcasting and connecting other clients.
For example, if you have configured your router to repeat the 2.4 GHz network of your main router or access point, you can change the wireless settings of the 5 GHz frequency band on your router, which can be used for broadcasting and connecting other clients. You can edit the wireless settings in the Wireless widget for both frequency bands.
## How to reset your Linksys Wrt120n router to factory defaults in wireless repeater mode?
If you encounter any problems with your router in wireless repeater mode, such as not being able to access its web-based setup page, having slow internet speed, or losing connection frequently, you can try resetting it to factory defaults and reconfiguring it as a wireless repeater.
To reset your router to factory defaults, follow these steps:
1. Locate the Reset button at the back of your router.
2. Press and hold the Reset button for about 10 seconds using a paper clip or a pin.
3. Release the Reset button when the Power LED starts blinking.
4. Wait for your router to reboot and become a regular router again.
After resetting your router to factory defaults, you will need to reconfigure it as a wireless repeater by following the steps in this article. You will also need to reconnect all your wireless devices to your network using the default wireless settings of your router.
## How to improve the security of your Linksys Wrt120n router in wireless repeater mode?
One of the most important aspects of setting up a wireless network is ensuring its security. If your network is not secure, unauthorized users may be able to access your internet connection, your personal data, or your devices.
To improve the security of your router in wireless repeater mode, you can do the following:
- Use a strong and unique password for your router's web-based setup page. This will prevent anyone from accessing and changing your router's settings without your permission.
- Use a strong and unique password for your wireless network. This will prevent anyone from connecting to your network without your permission. You can also use a different password for each frequency band on your router, which can be used for broadcasting and connecting other clients.
- Use a secure encryption method for your wireless network. This will prevent anyone from intercepting and reading your data as it travels through the air. The supported encryption methods for your router in wireless repeater mode are WPA-Personal, WPA2-Personal, and WPA-Mixed-Personal. You can choose the same encryption method as your main router or access point, or a different one if you prefer.
- Change the default network name (SSID) of your router. This will make it harder for anyone to identify and target your network. You can also use a different network name (SSID) for each frequency band on your router, which can be used for broadcasting and connecting other clients.
- Disable the Wi-Fi Protected Setup (WPS) feature on your router. This feature allows you to connect devices to your network by pressing a button or entering a PIN code, but it can also be exploited by hackers to gain access to your network. To disable this feature, go to Connectivity > Internet Settings > Wireless Repeater and uncheck the Enable Wi-Fi Protected Setup checkbox.
## How to optimize the performance of your Linksys Wrt120n router in wireless repeater mode?
Another important aspect of setting up a wireless network is ensuring its performance. If your network is not performing well, you may experience slow internet speed, poor signal quality, or frequent disconnections.
To optimize the performance of your router in wireless repeater mode, you can do the following:
- Choose the best location for your router. Place it in a central and elevated position that is close enough to receive a strong signal from your main router or access point, but far enough to cover the area where you need better Wi-Fi coverage. Avoid placing it near metal objects, walls, or other sources of interference that can weaken the signal.
- Choose the best channel for your router. Use a different channel than your main router or access point to avoid interference. For example, if your main router or access point is using channel 1 on the 2.4 GHz band, set your router to use channel 6 or 11 on the same band. You can also use a tool such as Wi-Fi Analyzer or inSSIDer to scan the available channels and find the least congested one.
- Adjust the antennas of your router. Position them vertically and point them in different directions to improve the signal quality and direction.
- Update the firmware of your router. This will fix any bugs or improve its performance. To update the firmware of your router, go to Connectivity > Basic > Firmware Update and follow the instructions.
## Conclusion
# Configurar Router Linksys Como Repetidor Wrt120n: Tips and Tricks for a Faster and More Reliable Wi-Fi Network
In this article, we have shown you how to configure your Linksys Wrt120n router as a wireless repeater and improve your internet coverage. We have also given you some tips on how to improve the security and performance of your router in wireless repeater mode. By following these steps, you can turn your router into a Wi-Fi extender and enjoy a faster and more reliable Wi-Fi network in your home or office. We hope you found this article helpful and informative. If you have any questions or feedback, please feel free to leave a comment below. Thank you for reading! b99f773239
https://www.progreva.com/group/progreva-group/discussion/59d27d99-f836-42a0-afdb-da8ec197f959